Ihr Warenkorb ist leer
Ihr Warenkorb ist leerEin ACDelco GM Original Equipment Motor-Kurbelwellenpositionssensor überwacht die Position und Drehgeschwindigkeit der Kurbelwelle und ist ein von GM empfohlener Ersatz für das Originalteil Ihres Fahrzeugs. Das Signal vom Kurbelwellenpositionssensor wird vom Motorsteuermodul zur Bestimmung der Kraftstoffeinspritzung und Zündzeitpunkt verwendet. Dieser Original-Motor-Kurbelwellen-Positionssensor wurde für Ihr GM-Fahrzeug hergestellt und bietet die gleiche Leistung, Haltbarkeit und Lebensdauer, die Sie von General Motors erwarten.
Mike B.
Bewertet in den USA am5. Juni 2019
These were for my 2003 Cadillac Deville DTS. It was NOT an easy job getting the old sensors removed due to the fact that they are directly behind the motor mount. It was too big of a job to remove the motor mount, so I removed the oil filter adapter to gain access from the left side. However, it was very difficult getting the electrical connectors off, especially from the upper sensor! I'd say it took me about 8 hours to complete the replacement working from underneath on my back. I HOPE these last a LONG time, but if I had to do this same job again, I'm sure I could do it in less than 4 hours start to finish now that I know exactly what to do.
Laika Lou
Bewertet in den USA am21. September 2015
Crankshaft Position SensorS…Northstar has 2 mounted forward block behind front motor mount and oil filter.If your 2000-05 Cadillac Deville suddenly stutters or stalls, these sensors (this item plus: 213-1579) may be the answer.Factory fit were inferior Mexico made, while there are superior Japan made items.I got them both and installed simultaneously…why sold separately is anyone's guess.They're color coded and shaped differently, so almost impossible to fit wrong.Job took me almost 30 minutes, including (cannot be too careful!) jackstand placement, etc.Engine stumble-stutter problem has not recurred since the swap.~~
Kevin Helgeson
Bewertet in den USA am2. April 2014
Don't go for any other than ACDelco if you want the right part for the right fix. A price is nothing for the quality, would recommend to anyone who needed it.
Troy V
Bewertet in den USA am8. Juni 2013
AC Delco OEM part, good price, great shipping, very happy. Was a little difficult to install, not the fault of the part, but the designer of the car. Allow about 1 hour or so to install. 2003 Oldsmobile Aurora 4.0 V8 Northstar motor. Block rear wheels, jack up car, place jack stands under engine cradle, lower car onto jack stands, remove lower front splash shield, remove brake line bracket from engine cradle, pull back brake lines for access, 10mm deep & shallow socket 1/4 inch ratchet, remove wiring harness by pushing in lock pin on clip & pull out wiring socket from upper CKPS, remove 10mm bolt, pry old CKPS from engine (should pop out relativity easy), apply engine oil to new CKSP seal & install new part & reverse removal order. Make sure to replace lower at the same time, if the one you are replacing is bad, the other probably isn't far behind. Your arm may get a little cut up as you will be working in a small confined area, so be careful. The CKPS is located next to/behind the center motor mount (front) by the oil filter & oil pressure sensor. None of these items need removal to replace the CKPS. If you have a 1/4 swivel & a short 10mm socket, you may have a easier job replacing the sensor. There are some blogs that say the ECM may need a relearn procedure, but I didn't do that & my car ran just fine. Good luck.
basscatt
Bewertet in den USA am3. Juli 2013
if you got the fault code P0335 -these updated sensors will cure your stalling problems caused by the old sensors -ALWAYS replace BOTH the upper and lower sensors -the other sensor is #213-1579 -and as of July 2013 - Amazon has the best price with free shipping -THANKS Amazon -
Produktempfehlungen
